CellarTech South West Ltd
Basement & Cellar Conversion
Basements & Cellars Supplied & Built
Serving Gloucestershire & the South West


 

 

John Newton Products used by CellarTech South West




Newton 503 (M5)
500 System - Cavity Drain Waterproofing



3mm Cavity Drain Membrane for Basement Walls, Floors & Vaulted Soffits


Newton 503 is a high quality BBA approved cavity drain waterproofing membrane suitable for use internally to retaining walls, vaulted soffits and floors.

Newton 503 is a flexible HPDE membrane which at 0.5mm in thickness and provides a quality low profile drainage solution within the Newton Cavity Drain membrane range.

Newton 503 (M5) is supplied in rolls 2m x 20m 40m2





Newton 503 Mesh (M11 & M12)
500 System - Cavity Drain Waterproofing



3mm Meshed Cavity Drain Membrane for Basement Walls & Vaulted Soffits


Newton 503 Mesh is a BBA certified meshed membrane suitable for use as a waterproofing membrane when used below the ground as part of Newton System 500.
With its 3mm stud, Newton 503 Mesh is just 3.5mm in overall thickness, and is the preferred meshed membrane where space is of a premium. Its high quality meshed surface provides an excellent key for lime mortars, renders, plasters or dabbed plasterboard. When using our Newton 503 Mesh it is essential to use Newton MultiPlug or Newton NuSeal with WaterSeal Rope as a means of achieving a waterproof seal.

Newton 503 Mesh is supplied in roll sizes 1m x 20m achieving 20m2 (M11) and 2m x 20m achieving 40m2 (M12)





Newton 508 (M1 & M2)
500 System - Cavity Drain Waterproofing



8mm Cavity Drain Membrane for Basement Walls, Floors & Vaulted Soffits


Newton 508 is our high quality BBA cavity drain waterproofing membrane suitable for use internally below the ground to retaining walls, vaulted soffits and floors. The Newton 508 is the flagship membrane in our range and one of the most specified cavity drain membranes in the UK. The 0.7mm thick HDPE product allows for large industrial loads to be applied and the in line studs allow for a quick and cost effective installation minimal surface preparation.

Newton 508 is available in roll sizes 2.4m x 20m , 48m2 (M1) and 2m x 20m , 40m2 (M2).





Newton 508 Mesh (M3)
500 System - Cavity Drain Waterproofing



8mm Meshed Cavity Drain Membrane for Basement Walls & Vaulted Soffits


Newton 508 Mesh is a high quality BBA approved meshed cavity drain waterproofing membrane, suitable for use internally below the ground to retaining walls and vaulted soffits. Newton 508 Mesh is typically used where space prevents the use of a dry-lining frame or block wall as the wall finish or where a direct rendered or plastered finish is preferred to vaulted ceilings. The ability to apply direct finishes to the product give the professional water proofing designer flexibility to use the system in convoluted or confined basement areas where space is at a premium or where the original contours (features) of the property wish to be retained.
Newton 508 Mesh (M3) is supplied in rolls 2m x 20m giving a total of 40m2





Newton 520 (M4 & M13)
500 System - Cavity Drain Waterproofing



20mm Cavity Drain Membrane for Basement Floors


Newton 520 is a high quality BBA approved cavity drain membrane suitable for use above basement floor areas. The 20mm studded membrane allows for a massive flow rate to pass underneath the membrane and is specified where floor areas are of questionable quality or where it is anticipated that there may be a risk of severe water penetration.

Newton 520 is supplied in two sizes 2m x 20m equal to 40m2 (M4) or 2m x 10m equal to 20m2 (M13)

Typical Applications

- Applied to existing and new slabs which are of questionable quality.





Newton Basedrain
500 System - Cavity Drain Waterproofing



Drainage System


Newton Basedrain is the drainage system used most commonly within the Newton System 500 waterproofing system. The drainage system compromises a range of products that collectively receive water ingressing at weaknesses within the structure and then discharge the collected water to a Newton Sump System or safe drainage (drainage that is below the level of the basement floor that cannot back-up or block):

Basedrain - Drainage conduit for the perimeter of the area to be waterproofed. Is situated at the base of the wall membrane
Floordrain - Drainage Conduit for collection of water at construction joint to the floor and to replace Basedrain at door thresholds. Floordrain is also used to connect the perimeter Basedrain to the sump.
Basedrain Corner Formed 90 degree corner.
Basedrain T Piece Formed T for a 90 degree connection to Floordrain from Basedrain.
Basedrain Extended T Piece For draining through engineering brick as an alternative to open perpendicular joints.
Jetting & Access Point - for inspection and maintenance access to the drainage system.





Newton Baseboard
500 System - Cavity Drain Waterproofing



Drainage Conduit


Newton Baseboard is a unique above slab drainage conduit that is designed to capture water that is entering properties via the wall/floor junction for removal to an appropriate drainage medium.

Prior to installing the Newton Baseboard System, mechanically fix a Newton Drainage Membrane to the retaining wall. Apply Newton MultiPlugs at 1m centres and affix the Baseboard Hanger in the head of the plug. The Baseboard is then clipped tight over the hanger to hold the linear lengths of the conduit into position. Use the Baseboard jointing pieces to form a continuous length of the conduit. Apply an epoxy band of 150mm to the wall floor junction fillet as a key for the Newton One Shot Adhesive. The waterproof bond between the One Shot and the epoxy allows for ingression of water to travel within the Baseboard to a predetermined drainage outlet for removal. Newton Baseboard preformed internal and external corners and stop-ends are also required.

Newton Baseboard is a patented US product only available in the United Kingdom from John Newton & Company.